8X1 4k 60Hz HDMI Multiviewer HDCP 2.2 HDBaseT 70 Meters Output Port

8X1 4k 60Hz HDMI Multiviewer HDCP 2.2 HDBaseT 70 Meters Output Port

1. Introduction

The 8X1 4k 60Hz HDMI Multiviewer HDCP 2.2 HDBaseT 70 Meters Output Port supports 9 inputs including 3 HDMI ports, 1 VGA(YPbPr/CVBS) and 1 DisplayPort, scaling to HDMI and HDBaseToutputs (Mirrored). It offers flexibility application of audio which includes unbalance audio, MIC In and line out. The audio processor offers auto-mixer and auto-gain control to mix or reduce background audio in order to enhance major audio source. The system could be controlled and configured easily via Telnet, WebGUI, IR remote and RS-232. This switcher is a suitable solution for presentation purpose at classroom and conference room.

2. Features

• HDMI 2.0b, HDCP 2.2 compliant

• 3xHDMI, 1xVGA(YPbPr/CVBS), 1xDisplayPort, 1xMIC In, 4xunbalance audio input

• HDMIand HDBaseT(70M) outputs (Mirrored)

• HDMI/DP video resolutions up to 4K2K@60Hz(4:4:4),4K2K@30Hz, 1080p@120Hz

• VGA resolutions up to 1920x1200@60Hz

• Output resolutions up to 4K2K@30Hz

• Support automatic and manual switching modes

• Supports EDID management

• Supports pass-through of PCM 2CH

• Touch Panel button,WebGUI, IR remote, Desk Plate and RS-232 control

3. Package Contents

• 1x5x1 4K60 Presentation Switcher

• 1 x HDBT Receiver

• 2 x Mounting ears

• 1 x Remote Control Unit

• 2 x IR Receiver Cable(with carrier wave)

• 2 x IR Emitter Cable

• 1x 24V/1A Power Adapter

• 1 x 3RCA(Female) to D-SUB(Male) Cable

• 1 x User Manual

• Pictures for 8X1 4k 60Hz HDMI Multiviewer HDCP 2.2 HDBaseT 70 Meters Output Port；

4. Specifications

​

5. Operation Controls and Functions

1.1 Front Panel

❶ Power button and indicator:

When this device is switched to the standby mode by pressing power button, theindicator will illuminate red.When switching to power on mode, theindicator will illuminate blue.

❷IR Window:

Receiving IRsignal from remote control.

❸ Input Source buttons:

Press these buttons for source selection. The active source will be illuminated to corresponding indicators on the front panel.

❹Operation buttons:

² Pressing“OK/MENU” button enters the OSD immediately. Then the user can navigate using the 4-way arrow buttons. A new OSD setting is confirmed by pressing “OK/MENU” button.

² Pressing"EXIT/AUTO" will exit OSD when OSD is displayed. Press"EXIT/AUTO" for 5 seconds to auto switch on/off. When the button LED light on, means auto switch on.

² Pressing “MIC-/+” buttondecreases or increasesMIC volume. Press “VOL+/-“ button to increaseor decrease “Master volume”.

² Pressing “MIC-“ and “MIC+” buttons simultaneously will resets the switcher HDMI/HDBT output resolution to 720P/60.

² Pressing “VOL-“ and “VOL+” buttons simultaneously will lock/unlock the front panel, these two button LED will light on when the front panel is lock on.

1.2 Rear Panel

❶

Control ports:

• LAN: This port is the link for Web GUI control; connect to an active Ethernet link with an RJ45 terminated cable.

• RS-232: Serial control port, 3P captive screw connector, connects with a control device (such as a computer) to control the switcher or other device connected with the HDBT receiver.

• IR IN: Connects with IR receiver cable (with carrier wave), to receive IR signals sent by theIR remote or remote controller of other input/output device.

• IR OUT: Connects with IR emitter cable used for controlling the local sourcedevice or the switcher.

• CONTACT IN: This input control reserving for direct source input selection. Connect ground pin (mark ason panel) with following pin number for individual source selection.

❷

Audio Ports:

• OUT: The audio comes from the input audio corresponding to the selected video source and mixed with MIC audio. Connects with amplifier for audio source broadcasting.

• EXT1/EXT2/EXT3/EXT4/EXT5: Select the external analog audio on OSD/WebGUI and insert the audio to HDMI1/2/3/DP/VGA video source then output to display and analog audio output port. The VGA Source select the EXT5 as default audio input.

• MIC IN: Plug microphone in for audio source output.

• 48V/MIC/Line :

❸48V phantom power mode (connects with phantom condenser microphone), MIC mode (connects with dynamic microphone and electrets condenser microphone) and LINE mode (connects with wireless microphone or line audio input).

Output Ports

• HDBT Out: Connects with compatible Receiver for video and / or audio output. Support 24V POC function.

• ❹HDMI Out: Connect to an HDMI display or AV Receiver for video and/or audio output.

Input Ports

These video input ports include 3 HDMI inputs, 1 Display Port input &1 VGA input. VGA port support VGA, YPbPr and CVBS format. Factory default is VGA format.

❺USB Port
USB port connects with USB flash disk or other storage that contains the software update file to update the system firmware.

❻Power:

Plug the 24V DC power supply into the unit and connect the adaptor to an AC outlet.

6.Connection Diagram

• Connect HDMI source devices (e.g. Blue-ray DVD) to HDMI input ports of the switcher with HDMI cable. Connect VGA source device (eg.PC/Note-book) to VGA input port of the switcher with a VGA cable.

• Connect HDMI display device to the HDMI output port of the switcher with a HDMI cable.

• Connect UTP Cable to the HDBT receiver.

• Connect speaker, headphone or specialized amplifier to AUDIO output port ofthe switcher.

• Connect control device (e.g. PC) to RS-232 port of the switcher.

• Connect DC24V power adaptor to the power port and power on.